Electromagnetic Compatibility Directive

Table of Contents


The EMC Directive 2014/30/EU applies to a vast range of equipment encompassing electrical and electronic appliances, systems and installations. This Directive covers products which are new to the Union market when they are placed on the market, as well and it applies to all forms of supply, including distance selling, as well.

The Directive 2014/30/EU applies to:

  • Electrical and electronic appliances, systems, and installations including electrical and electronic appliances;
  • Fixed installations;
  • Devices and sub assemblies intended to be included in an apparatus by the end user and mobile installations.

This directive shall not apply to:

  • Equipment covered by the Radio and telecommunication terminal directive (R&TTE) and Radio Equipment Directive (RED);
  • Radio equipment used by radio amateurs;
  • Equipment where EMC is covered by other specific directives, such as marine equipment if covered by Directive 96/98/EC or active implantable medical devices under the 90/385/EEC Directive;
  • Aeronautical products;
  • Equipment incapable of generating or contributing to electromagnetic emissions and/or operates without unacceptable degradation in the presence of electromagnetic disturbance as normally seen in its intended use;
  • Custom built evaluation kits destined for professionals to be used solely at research and development facilities for such purposes.

The Directive: EMC 2014/30/EU

The EMC Directive 2014/30/EU (Electromagnetic Compatibility Directive) of the European Parliament and of the Council was published on March 29, 2014 in the Official Journal of the European Union, L 96/79, and replaced Directive 2004/108/EC on the 18th April 2014.

The EMC Directive 2014/30/EU regulates the electromagnetic compatibility of equipment –  apparatus and fixed installations.

In order to achieve this objective, equipment need to comply with the essential requirements of the EMC Directive when it is placed on the market and/or put into service. The requirements limit electromagnetic emissions to a level that will not affect radio and telecommunications or other equipment and require products to have immunity to electromagnetic disturbances.

  • Chapter 1: General provision – Article 1-6
  • Chapter 2: Obligation of economic operators – Article 1-12
  • Chapter 3: Conformity of equipment – Article 13-19
  • Chapter 4: Notification of conformity assessment bodies – Article 20- 36
  • Chapter 5: Union market surveillance and control of apparatus entering the Union market ad Union safeguard procedure – Article 37-40
  • Chapter 6: Committee, Transitional ad final provisions – Article 41- 47
  • Annex I: Essential requirements
  • Annex II: Module A: Internal production control
  • Annex III: Part A – Module B: EU-type examination; Part B – Module C: conformity to type based on internal production control
  • Annex IV: EU declaration of conformity
  • Annex V: Time-limit for transposition into national law and date of application
  • Annex VI: Correlation table

Path to EU Market Entry

There are two potential paths that a manufacturer may elect to follow before making their products available on the EU Market.

Conformity Assessment Procedure

  1. Internal Production Control

(Annex II)


2. Conformity to type based on internal production control + EU-type Examination (Annex III)

Technical Documentation

It must be prepared by the manufacturer and shall include an adequate analysis  and assessment of the risk(s). The technical documentation shall be drafted up according to the conformity assessment procedure followed by the manufacturer.

Essential requirements for all equipment

Equipment shall be so designed and manufactured as to ensure that:

  • The electromagnetic disturbance generated does not exceed the level above which radio and telecommunications equipment or other equipment cannot operate as intended;
  • It has a level of immunity to the electromagnetic disturbance to be expected in its intended use which allows it to operate without unacceptable degradation of its intended use.

Specific requirements for fixed installations

Fixed installations shall be installed applying good engineering practices and respecting the information on the intended use of its components.

Authorized Representative

Post-Market Surveillance

Risks of Non-Compliance

The non-compliance with the directive’s requirements will result in the removal of the apparatus from the market and the revoking of the CE marking affixed on the apparatus.